Solaro QR, FR

Solaro series are a modular DSP configured using IO plug-in cards.

Amy avatar Andrea avatar
17 articles in this collection
Written by Amy and Andrea

How do I capture a USB boot log file to verify USB communication between a Xilica processor and my host computer?

If you cannot complete a USB BIOS or Recovery Firmware update, it may be necessary to capture the USB boot log to verify communication.
Andrea avatar
Written by Andrea
Updated over a week ago

What network ports does Solaro use for communication?

Solaro TCP and UDP network port information is listed below.
Andrea avatar
Written by Andrea
Updated over a week ago

FR Dante module Installation

Learn how to install and remove the optional FR Dante module by following the instructions below.
Andrea avatar
Written by Andrea
Updated over a week ago

FR1/XIO-16 Front Panel settings

The FR1 and XIO-16 processors front panel displays the device system information, network settings, and card slot configuration information.
Andrea avatar
Written by Andrea
Updated over a week ago

Are back-up files stored in Solaro?

Solaro Series DSP will automatically save a back-up project file to all Solaro DSPs in the project when going online.
Andrea avatar
Written by Andrea
Updated over a week ago

How do I change the sampling rate of my device?

Devices with selectable sampling rate option must match in software and hardware in order for the new sampling rate to take effect.
Andrea avatar
Written by Andrea
Updated over a week ago

Solaro IO Option Card USB BIOS Upgrade.

Solaro IO Option cards USB BIOS upgrade can be achieved by following a few simple steps.
Andrea avatar
Written by Andrea
Updated over a week ago

What are the QR1's PoE requirements and current draw?

The QR1 can be powered either by external power supply or PoE. The QR1's PoE requirements and current draw are as follows.
Andrea avatar
Written by Andrea
Updated over a week ago

How do I activate my AEC license?

Solaro Series processors have software activated AEC. To activate your Solaro Series AEC, please follow the instructions below.
Andrea avatar
Written by Andrea
Updated over a week ago

Is there a Rack Mount Kit available for the Solaro QR1 or XIO-8?

Easily rack mount one or two Solaro QR1 using the QR1-RMKIT.
Andrea avatar
Written by Andrea
Updated over a week ago

Solaro Front Panel USB BIOS Upgrade.

Solaro front panel USB BIOS upgrade must be upgraded along with new firmware. Learn how to perform the front panel BIOS upgrade below.
Andrea avatar
Written by Andrea
Updated over a week ago

How do I boot the device into diagnostic mode?

Solaro devices have built-in diagnostic mode. Diganostic mode tests the physical connection of the Ethernet port and the Dante port.
Andrea avatar
Written by Andrea
Updated over a week ago

Solaro Mainboard USB BIOS Upgrade.

Solaro mainboard USB BIOS upgrades must be upgraded along with new firmware. Learn how to upgrade the mainboard BIOS below.
Andrea avatar
Written by Andrea
Updated over a week ago

What do I do if my Solaro O/S is corrupted?

If your Solaro O/S is corrupted by powering Off or disconnecting the device during Firmware upgrade, a Firmware recovery must be performed.
Andrea avatar
Written by Andrea
Updated over a week ago

Can I use Solaro Series DSP with a Neutrino Series DSP in the same project?

Solaro Series and Neutrino Series DSP are separated into two separate project files in Xilica Designer. Learn about their differences below.
Amy avatar
Written by Amy
Updated over a week ago

How do I associate an XTouch design to a Solaro Series DSP?

Users can associate an XTouch design to Solaro Series DSP and store the design in the Solaro Series DSP.
Andrea avatar
Written by Andrea
Updated over a week ago

What is the Project Scheduler and how can I use it?

The Project Scheduler can trigger specific actions/events based on a programmable schedule. This feature is built into Solaro Series DSP.
Andrea avatar
Written by Andrea
Updated over a week ago